We compare published specs and prices. When you buy through our links, we may earn a commission. How we research
INFRARED SAUNA FOR HOME

Home / Guides / Wiring and placement

Infrared sauna electrical requirements: circuits, volts and plugs

Most wiring surprises show up on delivery day. A few minutes with the spec sheet and your breaker panel avoids them.

Updated November 20, 2026 · Specs compared from published manuals, not tested in person

Round wooden sauna interior lit in red

Short answer. An infrared sauna needs a dedicated circuit. Most 1 and 2 person cabins run on 120 volts with a 15 or 20 amp circuit, Bigger cabins need either a 20 amp, 120 volt circuit or a 240 volt circuit, depending on their heater power. The exact requirement is on the specification sheet of each model, and it is the only number that counts.

Key facts

  • An infrared sauna should be on a dedicated circuit, meaning the breaker feeds the sauna outlet and nothing else.
  • Most 1 and 2 person infrared saunas run on 120 volts and draw about 10 to 16 amps, so they need a 15 or 20 amp circuit.
  • Larger infrared saunas of about 3 kW and more, which includes many 4 person and outdoor models, commonly need a 240 volt circuit of 20 or 30 amps.
  • A 20 amp, 120 volt sauna plug has one sideways blade and does not fit a standard 15 amp household outlet.
  • Infrared sauna manuals generally say not to use an extension cord or a power strip.

Does an infrared sauna need a dedicated circuit?

Yes. A dedicated circuit means one breaker that feeds one outlet, used only by the sauna.

The reason is simple. A sauna is a steady load. It draws close to its full power for the whole session, often 30 to 60 minutes. Electricians commonly size a circuit so that a long-running load uses no more than about 80 percent of the breaker rating. A sauna already sits near that line on its own. Add a freezer, a treadmill or a space heater on the same breaker and it trips.

Before you order, find out what else is on the outlet you plan to use. Switch the breaker off and see which lights and outlets go dead. If anything else is on it, plan a new circuit.

How many amps does an infrared sauna use?

Amps are watts divided by volts. A 1,500 watt cabin on 120 volts draws about 12.5 amps. A 4,000 watt cabin on 240 volts draws about 17 amps.

Cabin sizeTypical powerTypical drawUsual circuit
1 personAbout 1.0 to 1.5 kWAbout 9 to 13 A at 120 V120 V, 15 A dedicated
2 personAbout 1.5 to 2.2 kWAbout 13 to 18 A at 120 V120 V, 15 or 20 A dedicated
3 personAbout 2 to 2.8 kWAbout 16 A at 120 V, or 9 to 12 A at 240 V120 V 20 A, or 240 V 20 A
4 person and upAbout 2.1 to 5 kW or moreAbout 17 A at 120 V, or 12 to 22 A at 240 V120 V 20 A on lighter models, or 240 V 20 or 30 A

These are common ranges, not a rule. Full spectrum heaters, outdoor models and cabins with more panels can sit higher. Read the watts, volts and amps on the spec sheet, then show them to a licensed electrician.

Infrared sauna 120V vs 240V: what is the difference?

120 volts is the normal household outlet. 240 volts is the kind of circuit used by a clothes dryer or a range. Neither makes a sauna better. A 240 volt circuit simply carries more power, which a large cabin needs.

  • 120 V cabins are usually 1 to 3 person models, plus some 4 person far infrared cabins with modest heater power. They come with a cord and plug. If a suitable dedicated outlet is already there, no electrical work is needed.
  • 240 V cabins are usually the larger and more powerful ones: many 4 person and bigger cabins, full spectrum models and large outdoor models. They need a new two-pole breaker and a new cable run. Some plug into a 240 volt outlet, others are wired directly.

Running cost follows the watts and the time, not the voltage. See how much electricity an infrared sauna uses.

What do 15 amp and 20 amp plugs look like?

They look different on purpose, so a 20 amp appliance cannot go into a 15 amp outlet.

  • 15 amp, 120 V plug: two flat vertical blades and a round ground pin.
  • 20 amp, 120 V plug: one vertical blade, one sideways blade and a ground pin. The matching outlet has a T-shaped slot on one side.
  • 240 V plugs: larger, with blades set in a different pattern. They fit only a matching 240 volt outlet.

A T-slot outlet on the wall does not prove the circuit is 20 amps and dedicated. Check the number on the breaker handle too. If the plug on the sauna does not fit the wall, do not use an adapter and do not swap the outlet yourself. The wire in the wall has to match the breaker, and that is a job for an electrician.

Can you use an extension cord?

No, according to most manuals. Light-duty cords heat up under a steady load, and power strips are not made for heaters. Sauna cords are typically only a few feet long, so the outlet has to be close to where the cabin stands. Decide the exact position first, then have the outlet placed for it.

Does an infrared sauna need a GFCI outlet?

This is the one point where manuals and local rules can pull in opposite directions.

A GFCI is the outlet or breaker with test and reset buttons. It cuts power when it senses current leaking to ground. Some sauna makers ask for a non-GFCI outlet, because certain heaters can trip the device without a real fault. At the same time, electrical codes in many areas call for GFCI protection in garages, unfinished basements and outdoors.

Give the manual to a licensed electrician, or call the local building department, and follow what they say for your address. This matters most for a garage or basement sauna and for an outdoor infrared sauna.

What does an electrician charge for a sauna circuit?

If a dedicated outlet of the right type is already in place, the cost is nothing. Otherwise it depends mostly on distance and on your panel.

  • Short run, free slot in the panel: a new 120 volt outlet near the panel is a small job, commonly a few hundred dollars.
  • Long run or finished walls: the price climbs with each foot of cable and each wall that has to be opened.
  • 240 volt circuit: more than a 120 volt one, because of the heavier cable and the two-pole breaker.
  • Full panel: if there is no free slot or no spare capacity, a subpanel or a panel upgrade can cost more than the sauna circuit itself.

Ask for a quote before you buy the cabin, and ask whether a permit is needed. See what an infrared sauna costs in total.

Checklist before you order

  1. Read the volts, amps and plug type on the spec sheet.
  2. Find a matching outlet within reach of the cord, or plan one.
  3. Confirm that the breaker feeds nothing else.
  4. Ask an electrician about GFCI for that location.
  5. Look for an ETL or UL listing on the cabin's electrical system. See warranty and certifications.

Common questions

Does an infrared sauna need a dedicated circuit?

Yes, in nearly every manual. A sauna pulls close to the limit of its circuit for the whole session, so anything else on the same breaker can trip it.

Can I plug an infrared sauna into a regular outlet?

Many 1 and 2 person cabins use a standard 120 volt, 15 amp outlet, as long as that outlet has its own circuit. Larger cabins need a 20 amp outlet or a 240 volt circuit, so check the spec sheet first.

Is 240 volts better than 120 volts for an infrared sauna?

Not better, just larger. 240 volts lets a cabin run more heater power, which bigger cabins need. A small cabin on 120 volts warms up fine.

Can I use an extension cord with an infrared sauna?

Manufacturers generally say no. A long or thin cord can overheat under a load that runs for 30 to 60 minutes. Have an outlet installed within reach of the sauna's own cord instead.

Does an infrared sauna need a GFCI outlet?

It depends on the model and the location. Some manuals ask for a non-GFCI outlet, while local code often requires GFCI protection in garages, basements and outdoors. Ask a licensed electrician which rule applies in your home.

Use the 30 second finder →

Keep reading

All 21 guides