We compare published specs and prices. When you buy through our links, we may earn a commission. How we research
INFRARED SAUNA FOR HOME

Home / Guides / Wiring and placement

How to assemble an infrared sauna: time, tools and steps

An infrared cabin is closer to flat-pack furniture than to a building project. The hard part is often carrying the boxes, not joining the panels.

Updated November 20, 2026 · Specs compared from published manuals, not tested in person

Wooden sauna interior with two levels of benches

Short answer. Two adults typically assemble a 1 or 2 person infrared sauna in about 1 to 2 hours with a screwdriver and a step stool. The panels buckle or clip together and the cables plug into each other. Larger cabins take 2 to 4 hours and are easier with a third person.

Key facts

  • Two adults typically assemble a 1 or 2 person infrared sauna in about 1 to 2 hours, and a 4 person cabin in about 2 to 4 hours.
  • Most infrared sauna cabins are made of 6 main panels: a floor, a back wall, two side walls, a glass front and a roof.
  • A 2 person infrared sauna commonly weighs about 250 to 400 pounds in total, split across two or three shipping boxes.
  • Infrared saunas usually ship by freight with curbside delivery, which means the boxes are left at the end of the driveway.
  • An infrared sauna can be taken apart and moved to a new house by reversing the assembly steps.

How long does it take to assemble an infrared sauna?

For most cabins, an afternoon covers everything from opening the boxes to the first warm-up. The joining itself is quick. Carrying, unpacking and reading the manual take as long as the build.

Cabin sizeTypical assembly timePeopleTypical total weight
1 personAbout 1 hour2About 200 to 300 lb
2 personAbout 1 to 2 hours2About 250 to 400 lb
3 personAbout 2 to 3 hours2 to 3About 350 to 450 lb
4 person and upAbout 2 to 4 hours3About 400 to 900 lb

These are common ranges for two adults working at a normal pace. Outdoor models with a separate roof cover, and cabins that screw together instead of buckling, take longer. The shipping weight and box sizes are on the spec sheet.

What arrives, and where is it left?

An infrared sauna usually ships by freight truck on a pallet, in two to four large flat boxes. Standard delivery is curbside. The driver lowers the pallet at the end of the driveway and leaves. Getting the boxes inside is up to you.

  • Book the delivery window. The freight company normally calls to set a day. Someone has to be home to sign.
  • Inspect before you sign. Look for crushed corners and torn cardboard. Note any damage on the delivery receipt and take photos. Glass and heater panels are the parts that suffer in transit.
  • Ask about upgrades. Some sellers offer threshold or inside delivery, or full installation, for a fee.
  • Have help ready. Boxes are too large and heavy for one person. If the weather is bad, open them at the curb and carry the panels in one at a time.

How heavy are the panels?

Each panel is usually manageable for two people. In a 2 person cabin, single panels commonly weigh about 30 to 80 pounds. The glass front and the back wall with its heaters are the heaviest. In a 4 person cabin, the biggest panels can pass 100 pounds, which is why a third person helps.

Size matters as much as weight. The largest panel is roughly as wide and as tall as the cabin. Measure doorways, stairs and tight turns before delivery day. The garage and basement guide lists what to measure.

What tools do you need?

  • A Phillips screwdriver, or a drill with a driver bit on a low torque setting
  • A step stool or short ladder for the roof connections
  • A box cutter and gloves for unpacking
  • A level, to check the floor before you start
  • A blanket or cardboard to rest the glass panel on

The screws, handles and brackets come in the box. No saw, glue or wiring tools are needed for a standard plug-in cabin.

How do you assemble an infrared sauna, step by step?

Every model has its own manual, and it takes priority. The usual order looks like this.

  1. Prepare the spot. Clear the area, check that the floor is level and confirm the outlet is within reach of the cord. Leave working room on all sides. You can slide the cabin back toward the wall at the end.
  2. Lay the floor panel. It has a front and a back. The floor heater, if there is one, faces up.
  3. Stand the back wall. One person holds it upright on the floor panel.
  4. Add the side walls. Each one locks to the back wall with buckles, clips or screws. Do not fully tighten yet.
  5. Fit the bench. The bench front, usually with the calf heater, slides into slots. The seat board rests on top.
  6. Set the glass front. Two people lift it into place and lock it to the side walls. Now tighten all the buckles.
  7. Lower the roof. Feed the cables from each wall through the holes in the roof panel as it comes down.
  8. Connect the cables. On top of the roof, each plug matches one socket, often by label or color. Push until they click. A cover board then hides the wiring.
  9. Finish. Fit the door handle, backrests and shelves. Plug in and run a first warm-up with the door closed, then air the cabin.

Do you need an electrician?

Not for the assembly. The connections inside the cabin are factory-made plugs. You need an electrician when the room has no suitable dedicated outlet, when the cabin needs 240 volts, or when the manual calls for a hardwired connection. Sort this out before delivery, using the electrical requirements guide.

Common mistakes

  • Building on an uneven floor. The door then rubs or will not stay shut. Level first.
  • Building against the wall. You need access to the outside buckles and to the roof.
  • Pinching a cable between the roof and a wall panel. Check each one before the roof settles.
  • Not enough ceiling height to lower the roof and reach the plugs. Check the manual for the gap needed.
  • Throwing the boxes away too soon. Keep them until the cabin has run properly, in case a part must go back.

Can you take it apart and move it?

Yes. This is one of the practical advantages of an infrared cabin over a built-in sauna or a steam room. Unplug it, remove the roof cover, disconnect and label the cables, lift off the roof and work backward through the steps. Wrap the glass front in blankets and move it upright. Keep the screws and the manual in a bag taped to a panel.

Before a move, check whether the warranty stays valid after relocation and whether the new room has the right circuit. See warranty and certifications. If you have not chosen a size yet, start with the sizing guide.

Common questions

How long does it take to assemble an infrared sauna?

Two adults typically need about 1 to 2 hours for a 1 or 2 person cabin and 2 to 4 hours for a 4 person cabin. Unpacking, carrying the panels and clearing the cardboard add time.

Can one person assemble an infrared sauna?

It is not a good idea. The wall panels have to be held upright while they are joined, and the glass front and roof are awkward to lift alone. Plan for two adults, and three for a large cabin.

What tools do I need to assemble an infrared sauna?

Usually very few: a Phillips screwdriver or a drill with a driver bit, a step stool and a box cutter. Many cabins join with buckles or clips and need no tools for the walls.

Do I need an electrician to assemble an infrared sauna?

Not for the cabin itself, because the internal cables are plug-in connectors. You need an electrician only if the room lacks the right dedicated outlet or the model is hardwired.

Can I take an infrared sauna with me when I move?

Yes. Unplug it, disconnect the roof cables, lift off the roof and separate the walls in reverse order. Label the cables and wrap the glass panel before the move.

Use the 30 second finder →

Keep reading

All 21 guides